Click on the picture to the right to view or print the exploded parts diagram for the Maytronics Dolphin Deluxe 4 Robotic Pool Cleaner. Click HERE for a Complete. Maytronics Dolphin Repair And. Dolphin Deluxe 4 pool cleaner gets stuck on the pool drain I have a Dolphin Deluxe 4 pool cleaner that gets.

1. English

A common problem, especially with 'newer' Maytronics Dolphin brand pool cleaners is that you put the unit in the pool, or even try to turn it on after a cleaning cycle while it is still in the pool, and to that point it has worked fine. You turn the power supply on and nothing happens. You turn it off and back on and still nothing. You leave it, even over night, same thing. What do you do? While I cannot tell you why it does this (we have a theory but can not confirm it) what usually works is to follow these steps. 1) Unplug everything.

Unplug the power supply from the outlet and the Dolphin from the power supply. 2) Let the whole thing sit a couple of minutes (we want to allow any capacitors to discharge). 3) Be sure the Dolphin is out of the water and sitting upside-down on a level surface (Tracks pointing skyward). 4) Reconnect the Dolphin to the power supply and the power supply to the outlet. 5) With the Dolphin still out of the water, perform a self-test. Simply turn on the Dolphin.

Within about 15 seconds it should begin to move. The tracks will spin in both directions with and without the impeller motor running at the same time. It is not unusual for the tracks to rotate at different speeds during this test. The test will last for 30 - 45 seconds or so. If it goes on indefinitely, turn it off and contact us for further direction. 6) Assuming the unit has now worked to this point, you should be able to put it back in the water and it will return to normal operation from this point on. If it still won't run; it runs a few moments and quits the self-test; or runs continuously, contact us thru the Dolphin service form along the bottom of our home page.

• Minigames: rhythm-based challenges and the same video game machines like the classic arcade game. • Theft: Sneaking into the houses and took valuables from occupants of the house. • Gang Wars: Battle of the gang enemy and must be defeated in order to defend the territory and enemy gang will no longer attack players.

On Dec 16, 2009. You can find this fuse in just about all online pool parts supply stores. When searching for the best deal.Use this info below. I would try radio shack first and see if they have the correct size/amp rating.

If not, order on-line. One site of many is. Good luck and hope this helps. Product Specifications Part #: 3295-023 Manufacturer: Maytronics Manufacture Code: 1930251 Product Dimensions: 0.75' X 0.25' Product Description INYO # MAYTRONICS # 1930251 GENERAL DESCRIPTION: THIS IS THE 2.5 AMP FUSE USED IN SOME DOLPHIN POWER SUPPLIES THIS IS A SMALL CLEAR GLASS FUSE LENGTH:3/4' DIAMETER: Aug 26, 2011.

Thank you for posting your question here on. You'll need to send it in for service. The power supply PCB and/or bridge are likely overheating causing the circuit breaker imbedded in the switch to trip. You may also have an issue with the cable or motor unit in the cleaner so they too will need to be checked. These repairs are best done by a service center.

For information on what centers are closest you can contact Maytronics at and they will send you repair information and a listing of service centers (we are one of them). If this answer does not fix your problem, please comment with additional details prior to rating the answer. Positive feedback is appreciated once your problem is solved! John Jun 27, 2010. If your unit has a fuse it will be on the back side of the power supply.

If the light on the power supply switch is on, it will not be the fuse though. Try turning the cleaner upside down on the deck and connect it as you otherwise would.

Power it up and it should go through a self test process that takes about 40 seconds to complete. If it turns the tracks in both direction with and without the impeller turning, it is fine and will likley start working in the pool again.

If not, contact us through and click on the FAQ and then Dolphin cleaner catagory. You can also use the Dolphin Serice button for information about sending it in for repair. Jul 03, 2009.

A common problem, especially with 'newer' Maytronics Dolphin brand pool cleaners is that you put the unit in the pool, or even try to turn it on after a cleaning cycle while it is still in the pool, and to that point it has worked fine. You turn the power supply on and nothing happens. You turn it off and back on and still nothing. You leave it, even over night, same thing.

What do you do? While I cannot tell you why it does this (we have a theory but can not confirm it) what usually works is to follow these steps. 1) Unplug everything. Unplug the power supply from the outlet and the Dolphin from the power supply.

2) Let the whole thing sit a couple of minutes (we want to allow any capacitors to discharge). 3) Be sure the Dolphin is out of the water and sitting upside-down on a level surface (Tracks pointing skyward).

4) Reconnect the Dolphin to the power supply and the power supply to the outlet. 5) With the Dolphin still out of the water, perform a self-test. Simply turn on the Dolphin. Within about 15 seconds it should begin to move. The tracks will spin in both directions with and without the impeller motor running at the same time. It is not unusual for the tracks to rotate at different speeds during this test. The test will last for 30 - 45 seconds or so.

If it goes on indefinitely, turn it off and contact us for further direction. 6) Assuming the unit has now worked to this point, you should be able to put it back in the water and it will return to normal operation from this point on. If it still won't run; it runs a few moments and quits the self-test; or runs continuously, contact us thru the Dolphin service form along the bottom of our home page. On Dec 16, 2009.

You can find this fuse in just about all online pool parts supply stores. When searching for the best deal.Use this info below. I would try radio shack first and see if they have the correct size/amp rating. If not, order on-line. One site of many is.

Good luck and hope this helps. Product Specifications Part #: 3295-023 Manufacturer: Maytronics Manufacture Code: 1930251 Product Dimensions: 0.75' X 0.25' Product Description INYO # MAYTRONICS # 1930251 GENERAL DESCRIPTION: THIS IS THE 2.5 AMP FUSE USED IN SOME DOLPHIN POWER SUPPLIES THIS IS A SMALL CLEAR GLASS FUSE LENGTH:3/4' DIAMETER: Aug 26, 2011. Thank you for posting your question here on. You'll need to send it in for service. The power supply PCB and/or bridge are likely overheating causing the circuit breaker imbedded in the switch to trip. You may also have an issue with the cable or motor unit in the cleaner so they too will need to be checked. These repairs are best done by a service center.

For information on what centers are closest you can contact Maytronics at and they will send you repair information and a listing of service centers (we are one of them). If this answer does not fix your problem, please comment with additional details prior to rating the answer. Positive feedback is appreciated once your problem is solved!

John Jun 27, 2010. If your unit has a fuse it will be on the back side of the power supply. If the light on the power supply switch is on, it will not be the fuse though. Try turning the cleaner upside down on the deck and connect it as you otherwise would.

Power it up and it should go through a self test process that takes about 40 seconds to complete. If it turns the tracks in both direction with and without the impeller turning, it is fine and will likley start working in the pool again. If not, contact us through and click on the FAQ and then Dolphin cleaner catagory. You can also use the Dolphin Serice button for information about sending it in for repair.

English

Jul 03, 2009.